Operators cleaning municipal sewer, storm and sanitary lines face a host of challenges on the job. This can range from having to clean miles of line in the most efficient manner, complying with annual regulatory mandates, to handling tough blockages caused by roots, grease, and cave-ins. It can even involve dreaded “blown toilets” – which can become a community clean-up and public relations nightmare if this occurs too often.

“Most of the problems are in 4-in. up to 18-in. sewer pipe, which accounts for up to 95 percent of all the pipe in the ground, anywhere in the United States,” says Dan Story, operations manager for KEG Technologies. “Proper training and education can resolve the majority of these issues.”

RELATED: Nozzles Optimize Sewer Crew Efficiency, Profitability

1. To Clean Faster, Slow Down

The number one mistake of most operators is simply rushing through the cleaning process, according to Story.

“Most operators run their nozzles way too fast. Slow your nozzle down and let it do its job. You’re not in a race. If you run the nozzle up in a hurry and back in a hurry, all you do is waste water and time,” says Story.

According to Story, when operators slow down and let the water flow carry the material back to the evacuation point, the water in the pipe becomes like a “conveyor belt that moves the material.”

“If you clean correctly, the water is going to carry the debris off and out of the way,” says Story. “That is why with 6 to 15-in. lines, 95 percent of the time it is possible to go from manhole to manhole and clean them in one pass. While I’m moving on, most operators who rush are still making second and third  passes.”

To stay productive, Story advises operators to never outrun their water.

“As you go in the pipe, if you go in slow enough, you should be running between 40 and 60 feet per minute, based on the condition of the pipe and how much material is in the pipe. The more material, the slower you want to move,” he says. “You want to be able to chop that material up and get it in the flow of the pipe’s stream. When you get to the end of the line, dial your pressure back down and rinse it. When you come back, the job is done.”

KEG Technologies sewer cleaning

2. Choose the Right Nozzle for the Job

In addition to going slow, Story emphasizes that choosing the right nozzle for the job is critical.
He points out that in many cases, using a high efficiency Tier-3 nozzle will provide significantly more cleaning force, at a greater distance, with less water. This enables crews to get more line cleaned before having to leave the jobsite to refill the sewer truck with water.

As is known throughout the industry, there are tiers of nozzles, rated for water efficiency from Tier 1 (about 30 percent efficient), Tier 2 (50-60 percent efficient), to Tier 3 (75-98 percent efficient).

According to Story, a Tier-1, 30-degree drilled nozzle running 72 gallons a minute at 2,200 psi will only exert 13 pounds of force to move debris 9 ft away from the nozzle. In contrast, a high-efficiency Tier-3 nozzle running 60 gallons a minute at 2,000 psi will impact that plate 9 ft away with 98 pounds of force.

KEG Technologies sewer cleaning

3. Slow Down Even More to Remove Blockages

While blockages come in many varieties, including roots, grease, mineral deposits and cave-ins, it is essential to clean even slower when encountering one, according to Story.

“If the operator rushes up the sewer line, sooner or later they will run into a blockage of roots, grease, etc. and plug up their front jets. Now, they no longer have a penetrating tool. They have a battering ram, a nozzle with no forward jets trying to feed its way through the blockage,” says Story.

He advises, “Instead, slow down even more to remove a blockage and let the nozzle do the work. The reason we put forward jets on those nozzles is so they can open the blockage before the nozzle arrives. By slowing it down, the water will open the blockage even before the nozzle ever gets there.”

RELATED: The Basics of Jetter Nozzle Maintenance: How to Clean Nozzles

4. Avoid Blown Toilets: Slow Down and Clean Up and Down the Sewer Line

As any operator knows, a blown toilet can occur when the operator rushes up the sewer line with little or no cleaning going up the sewer line on the first pass. This results in excessive piles of debris on the return trip through the same stretch of sewer line.

According to Ken Billingham, KEG international product specialist, air flow from the jet nozzle compresses between the nozzle and the debris, creating significant positive pressure. When the debris passes by a home’s service line, the pressurized air blasts up and out of the service line, causing a blown toilet.
The solution, he says, is to slow down and clean going down the sewer line and back. This can largely prevent the conditions that too often lead to blown toilets.

The same approach can prevent the worst incidents – when rotting black material trapped in sewer pipe sags gets launched into homeowner’s bathrooms.

KEG Technologies sewer cleaning

5. Set Up and Use Chain Cutters Correctly

Chain cutters can be used to remove most types of sewer line blockages. However, these tools must be set up and used correctly.

“Chain cutters are forgiving, but most people are hesitant to use them because if they are set up wrong or run improperly, they can destroy your pipe. If you set it up right, and run it properly, you will never damage a pipe,” says Story.

Story says that operators must first set up cutters correctly and follow the manufacturer’s guidelines. In general, he advises, it is best to set up the cutter chain to be about 1 in. smaller than the pipe it will cut i.e., use a 9-in. cutter chain in a 10-in. pipe.

As for operating the cutter, he says, “Let the tool find its way down. You will know when it’s in contact with roots. You can feel it. You can smell it. You can hear the change in the way that the tool works. Just keep feeding it in slow and steady until it gets through the problem.”

6. Use a Camera Nozzle to Quickly Determine the Problem or Verify Compliance

When municipalities need to quickly assess the condition of a sewer line to determine a solution or document its condition to verify mandated compliance, today nozzles with integrated cameras can accomplish both during routine cleaning.

“A small municipality could use a camera-nozzle to inspect their own pipes to verify they are clean instead of contracting it out. If they find any major problems, they could bring their contractor in,” says Billingham. “When the operator is having problems trying to get through a pipe, a camera-nozzle can take a quick look at it, so they can pick the right tool, whether it is a cutter, blockage nozzle or digging crew.”

Story adds an important word of caution, “Anytime you put a root cutter in any kind of pipe, the line should always be inspected with a camera first, and a camera nozzle makes this easy. Also, all cutting should be done with a camera to help the operator know what he or she is doing. This is critical because with all the varied utilities in the ground, if you’re not inspecting the pipe, you’re liable to hit electric lines, gas lines, or fiber optic lines – and that can cause explosions or serious outages.”

7. Conduct Industry Best-Practice Training to Optimize Safety and Production

Most municipal operators and contractors do not have the time to keep up-to-date with the industry’s best practices and equipment. That can lead to costly errors and even safety hazards.

For those who want to enhance the safety and productivity of their workforce, scheduling periodic or ongoing training can resolve serious issues and turn problems into strengths.

Del Williams is a technical writer who lives in Torrance, California.

See Discussion, Leave A Comment